• Welcome to Bare Knuckle Pickups Forum.
 

monte allums boss ge-7 eq pedal - short review

Started by gwEm, March 14, 2007, 01:21:25 PM

Previous topic - Next topic

gwEm

after doing the mod, almost any half-decent op-amp will p1ss over the junk that boss fitted in those ge-7s in my opinion
Quote from: AndyRyou wouldn't use the meat knife on crusty bread but, equally, the serrated knife and straight edge knife aren't going to go through raw meat as quickly

gwEm

Quote from: Twinfan on May 22, 2011, 09:26:20 PM
I did the full Plus kit in one go to a Taiwan made pedal.  It's fiddly, so take your time so you don't fry the board.  Use a solder sucker to clean the joints as you remove components.

I think I took a couple of hours or so with a few coffees and Rock Radio in the background!

curious to ask what you thought of the modded pedal?
Quote from: AndyRyou wouldn't use the meat knife on crusty bread but, equally, the serrated knife and straight edge knife aren't going to go through raw meat as quickly

andyg_prs

#17
I may get the kit...but with a gig coming up and shipping time 2 to 3 weeks, before it gets stuck in customs....I may just buy the capacitors and opamps and do it myself.

However, struggling where to find the NE5532AP op amp and sockets.  Well I've found Farnell for the op amp but not the sockets..

Any ideas?

Cheers,
Andy

Twinfan

I found the Monte Allums kit to be a MASSIVE improvement over the noisy and cr@p stock pedal.  It's a bit of a squeeze in there, and I've had to open it up a few times to cure a couple of grounding issues against the case (the chunky op-amp holders being the cause of this).

I bought my EQ pedal used, so for the £70 or so it's cost me in total I'm happy.  I use it for rehearsals, but my main rig for gigs has an Empress ParaEQ.


andyg_prs

Hi guys,

Turns out I have the older 4 op amp model, anyone know what capacitors need to be swapped?  Do you think just swapping out the op amps below would clean up the noise?

With this Kit you will receive three RC4559P and one TL072 Op-amp, three Tantalum Capacitors, one Metal Film Capacitor, four Boxed Metal Film Capacitors, Solder and Desoldering Braid along with detailed easy-to-follow Mod Instructions. NOTE: The kit for the newer GE-7 will only include threeRC4559P chips.

Cheers,
Andy

Twinfan

No idea mate - I just used the full kit and instructions, which are worth the price to me.

HairyChris

Heh, I ordered a Tonejam premodded one years ago when the dollar was weak (in spiffy matt black paint & OTT green LED). It sat in my kit box for ages but have recently been using it as a clean boost. It's dead silent and adds a nice kick to proceedings.
A-Pig 7s, Miracle Man & Mule, Cold Sweats... Expensive kit and no talent posse.

gwEm

Quote from: andyg_prs on May 24, 2011, 08:57:36 AM

Turns out I have the older 4 op amp model, anyone know what capacitors need to be swapped?  Do you think just swapping out the op amps below would clean up the noise?


yes it will. but you'll be missing out on some usability improvements. Monte's capacitor changes make the controls less spikey.
Quote from: AndyRyou wouldn't use the meat knife on crusty bread but, equally, the serrated knife and straight edge knife aren't going to go through raw meat as quickly

gwEm

Quote from: Twinfan on May 24, 2011, 09:17:46 AM
No idea mate - I just used the full kit and instructions, which are worth the price to me.

i agree, definately worth the price. plus monte is a real gentleman
Quote from: AndyRyou wouldn't use the meat knife on crusty bread but, equally, the serrated knife and straight edge knife aren't going to go through raw meat as quickly