• Welcome to Bare Knuckle Pickups Forum.
 

4 to 2 conductor

Started by ilÿti, October 31, 2007, 11:18:33 PM

Previous topic - Next topic

ilÿti

So, turns out I'm buying wintersun's Mule.

It happens to be 4-conductor though. Is there a way to wire this the same as with braided 2?

Thanks.
Crawlers, Mule-7s
The Danish parliament is working on an official apology for Lars Ulrich

WezV

solder the green and white wires together and tape them off.  You are left with red, black and a bare wire.  red is the hot wire black and bare go to ground
[url=http://www.wezvenables.co.uk]www.wezvenables.co.uk[/url]

ilÿti

Thanks Wez. But I didn't really understand any of that... what is ground what is hot?

Scematics, please.
Crawlers, Mule-7s
The Danish parliament is working on an official apology for Lars Ulrich

WezV

Hot is the one that either goes to the switch or the tag of the volume pot.  Ground is the one that goes to the back of one of the pots
[url=http://www.wezvenables.co.uk]www.wezvenables.co.uk[/url]

WezV

Quote from: ilytiScematics, please.

what guitar is it, and what controls does it have?
[url=http://www.wezvenables.co.uk]www.wezvenables.co.uk[/url]

ilÿti

Quote from: WezVHot is the one that either goes to the switch or the tag of the volume pot.  Ground is the one that goes to the back of one of the pots
Ahh, ok got it. Thanks.

It's a semihollow with normal Les Paul style switching/wiring. It's gonna be a mess to do the wiring work through the f-holes(or bridge pickup hole), but it seems possible.

http://img46.imageshack.us/img46/5507/raines001el3.jpg
Crawlers, Mule-7s
The Danish parliament is working on an official apology for Lars Ulrich

WezV

right - the hot (red) wire goes straight to the 1st tag on the volume pot and the ground (black and bare) goes to the back of that volume pot.

les paul style wiring has individual volumes for each pickup so the pickup has to go to the volume pot first rather than straight to the switch

assuming there is no backplate dont undo any of the parts till you have something tied around each pot.  Fishing line or thread will work but surgical tubing pushed over the post of each pot works so much better because it wont tangle.  

surgical tubing is now sold by guitar parts suppliers because it makes a great alternative to pickup springs.  

Its also a good idea to take an old dead lead and remove the jack plug.  This can then be attached to something like an old metal coat hanger and used to remove the jack socket. Not so much a problem on yours but on es335's it makes reattaching the jack socket a hell of a lot easier because you can guide it better and have something firmer to help put the nut on
[url=http://www.wezvenables.co.uk]www.wezvenables.co.uk[/url]

ilÿti

I think I saw that post a little too late haha. No damage done though. I found that I could get the pots out through the f-hole (the pots are very small), and I figured out which line goes to what. But it was hell getting them back in. Thanks for the tip with tying something on the post, I'll remember that next time  :wink:

Is this right?
Crawlers, Mule-7s
The Danish parliament is working on an official apology for Lars Ulrich

WezV

essentially thats it - but make sure the green and white get taped of so they cannot short anywhere
[url=http://www.wezvenables.co.uk]www.wezvenables.co.uk[/url]

ilÿti

Quote from: WezVessentially thats it - but make sure the green and white get taped of so they cannot short anywhere
You mean wrap some tape around the soldering point?
Crawlers, Mule-7s
The Danish parliament is working on an official apology for Lars Ulrich

WezV

[url=http://www.wezvenables.co.uk]www.wezvenables.co.uk[/url]

ilÿti

Crawlers, Mule-7s
The Danish parliament is working on an official apology for Lars Ulrich