• Welcome to Bare Knuckle Pickups Forum.
 

Nailbomb into Ibanez Universe

Started by Bekanor, February 10, 2009, 02:15:00 AM

Previous topic - Next topic

Bekanor

I'm trying to wire a nailbomb bridge in with the existing dimarzios in my UV777P and I've tried so many different combinations of colours and stuff with no result. Can anyone help me out?

reguv760

Doesn't the UV777P use a simpler 5 way switch?
If this helps, I think it's like:

DiMarzio red = BKP red
DiMarzio green = BKP black
DiMarzio black + white = BKP green + white

Reg

Bekanor

I think that's like the only combination I didn't try. I'll give it a shot now and let you know how I go.

Bekanor

Ok I have the black and bare wires going to the volume pot/ ground. The red on one switch terminal, the green and white on another. I'm officially out of ideas and am starting to suspect a dead pickup.

Will

Have you tried taping the coil split ones together, to see if the pickup works on its own?

WezV

do you have a multimeter to check if the pickup is dead?  if not attach it directly to the output jack to test it.

to do that you would connect the white and green together and tape them out of the way, then connect the red to the tip and black/bare to the sleeve of the jack socket

[url=http://www.wezvenables.co.uk]www.wezvenables.co.uk[/url]

Bekanor

Quote from: Will on February 10, 2009, 10:02:15 AM
Have you tried taping the coil split ones together, to see if the pickup works on its own?

No.


Is that the green and white?

Will

What is the Bare Knuckle Four conductor colour code?
Black =start of screw coil
White = finish of screw coil
Red = start of slug coil
Green = finish of slug coil

Did you check up the colour code? :P

Bekanor

Quote from: WezV on February 10, 2009, 10:05:15 AM
do you have a multimeter to check if the pickup is dead?  if not attach it directly to the output jack to test it.

to do that you would connect the white and green together and tape them out of the way, then connect the red to the tip and black/bare to the sleeve of the jack socket



I don't have a multimeter but the guy I got the Universe and the nailbomb from said he got it tested and it was ok. But he couldn't get it wired up either so I dunno.

I'll try it on the output jack and see how I go, I'll be pissed off if it's dead.

Bekanor

Quote from: Will on February 10, 2009, 10:26:08 AM
What is the Bare Knuckle Four conductor colour code?
Black =start of screw coil
White = finish of screw coil
Red = start of slug coil
Green = finish of slug coil

Did you check up the colour code? :P

http://www.guitarelectronics.com/c=VcyHC5oaDwzTAoZ9A5sXcZDnZ/category/wiringresources.pickup_color_codes/

I checked it on there, no idea if that's right or not.

This is so much easier with actives.  :lol:

Bekanor

Connected directly to the output jack it works fine.


Must be a less than solid connection on the volume pot.

Bekanor

Yay it works, it's just really noisy so yay for chasing down a bad ground.


Will

That site you linked to has the green and red the other way around I think (from what I copied and pasted from BKP FAQ's) But Wez seem to say differently, so maybe I have done something wrong

Bekanor

Well so far so good, it seems to be fine.


I'll have a better idea tomorrow when I run into my ENGL.


Thanks everyone!

FELINEGUITARS

BKP wiring colour codes are exactly the same as Tom Anderson if you look at sites that offer wiring diagrams for different makes
[url="//www.felineguitars.com"]www.felineguitars.com[/url] - repairs & custom built
Great fretwork!
Buy your BKPs & Earvana from ME!