• Welcome to Bare Knuckle Pickups Forum.
 

Faded /flat finish's. How do you make yhem shine?

Started by marantz1300, May 17, 2009, 07:50:08 AM

Previous topic - Next topic

marantz1300

I just got a Gibson smartwood Exotic. How do I make the flat finish shine.The top is Peroba.                                                                                                                      

Mr. Air

That's a very beautiful guitar. I don't know how to make it shine, but if it was my guitar I wouldn't change it. I like the look as it is.
Mississippi Queens, Stormy Monday/Apaches, Emeralds, Nailbomb (bridge)

indysmith

[size=9px]LOVING the Mules![/size]

Philly Q

As I mentioned in the other thread, you could just dive straight in with some T-Cut.

But I'm not sure (a) how thin the finish is (danger of rub-throughs) and (b) whether it'll turn out to be perfectly smooth if you polish it.

I agree with the guys, personally I'd leave it matt - then change the hardware to nickel to make it look less "furniture", more like a workhorse.
BKPs I've Got:  RR, BKP-91, ITs, VHII, CS set, Emeralds
BKPs I Had:  RY+Abraxas, Crawlers, BD+SM

marantz1300

Thats what I'm aiming for.Like the Briggs.But that was polished.

indysmith

Quote from: Philly Q on May 17, 2009, 01:15:13 PM
change the hardware to nickel to make it look less "furniture", more like a workhorse.
Ohhh good plan!
[size=9px]LOVING the Mules![/size]

Philly Q

#6
Quote from: marantz1300 on May 17, 2009, 02:00:19 PM
Thats what I'm aiming for.Like the Briggs.But that was polished.

Try polishing with T-Cut on an inconspicuous part of the guitar - maybe somewhere on the back, just a little bit to see how it looks. 

If it looks bad, you can get the finish back to matt with some wire wool, micromesh or fine wet/dry paper.  If it turns out OK you can take the plunge and do the rest of it!
BKPs I've Got:  RR, BKP-91, ITs, VHII, CS set, Emeralds
BKPs I Had:  RY+Abraxas, Crawlers, BD+SM

marantz1300

I'll  try a small area like under the pickup rings or under the switch ring.

gwEm

i used t-cut on a faded finish V and it works well to give a shine... but be careful - its easy to get t-cut stuck in the grain, and it doesn't look good! looking back, i would try a different way to shine it
Quote from: AndyRyou wouldn't use the meat knife on crusty bread but, equally, the serrated knife and straight edge knife aren't going to go through raw meat as quickly

pagan7

Short of giving it a couple of coats of clear laquer for a glossy finish, then liberal amounts of any beeswax based furniture polish well buffed will make it shine more but I agree with Phily - leave it as it is and change the "bling" hardwear for something more workmanlike.

p.s. avoid silicon based polishes as they can give a hazing effect on some finishes
CERAMIC NAILBOMBS + Ibanez RGT42DX and PAINKILLERS + Ibanez RG321MH and A5 NAILBOMBS + Ibanez RG1550

Tellboy

#10
My PRS Standard has a similar satin finish. I found that by regularly using a good quality guitar polish (I use Gibson and give the guitar a good clean/shine everytime I change strings) the guitar finish will get much shinier. Also I went for the chrome covers when I fitted the calibrated Cold Sweats
John Suhr - "Practice cures most tone issues"
Crawler,Mule,Apache,Piledriver,Bl. Guard,Cold Sweat

marantz1300

That looks great. I'll buy some guitar polish .